{"product_id":"nitro-save","title":"Nitro-Save® Humidity Control Monitor","description":"\u003cp\u003e\u003cstrong\u003eElectrical Requirements:\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eInput: 120VAC \/ 60Hz \/ 10W\u003cbr\u003e\nOutput: 9VDC \/ 500mA\u003cbr\u003e\nForeign plugs available upon request.\u003cbr\u003e\nNitro-Save® Operating Instructions\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eRetroFit Installation Instructions for Existing Desiccators\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe primary purpose of desiccators is to establish precise relative humidity levels to protect moisture sensitive materials in a clean environment. TDI has developed an economic, solid state system that accurately controls humidity and significantly reduces nitrogen consumption.\u003cbr\u003e\nThe Nitro-Save® Humidity Control Monitor significantly reduces the nitrogen required to maintain pre-set humidity (RH%) in TDI's Desiccator Cabinets up to 90%+ reduction in nitrogen consumption in many applications. (See Graph)\u003c\/p\u003e\n\u003cfigure id=\"attachment_2061\" aria-describedby=\"caption-attachment-2061\" style=\"width: 655px\" class=\"wp-caption alignnone\"\u003e\u003cimg class=\"wp-image-2061 size-full\" src=\"https:\/\/cdn.shopify.com\/s\/files\/1\/0991\/8477\/1391\/files\/mig-34bea3677b9b7e2b.jpg\" alt=\"Nitrogen savings chart 12 door\" width=\"655\" height=\"412\"\u003e\u003cfigcaption id=\"caption-attachment-2061\" class=\"wp-caption-text\"\u003eTDI Independent Test Results\u003c\/figcaption\u003e\u003c\/figure\u003e\n\u003cp\u003e\u003cstrong\u003eTDI Independent Test Results- Conditions May Vary by Application\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eThe Nitro-Save® includes a solenoid control valve and internal sensor system to regulate the nitrogen flow in response to the high humidity set point. Whenever the humidity rises 2% above the set point the control valve will turn on. Once the humidity decreases 2% below the set point, the control valve will turn off. Each time the control valve turns on, the monitor will begin a 2 hour timer. If at the end of 2 hours the humidity has not reached 2% below the set point, the High Humidity Alarm will sound. Under normal operating conditions the alarm at the end of the 2 hour cycle will indicate a problem such as a lack of nitrogen flow rate or the cabinet door remained open.\u003c\/p\u003e\n\u003cp\u003eThe High Humidity Set Point has been pre-programmed to 20% RH, which represents general electronics requirements. The RH % settings can be increased for less critical humidity control or decreased for more critical humidity control.\u003c\/p\u003e\n\u003cp\u003eTo maintain low moisture conditions in TDI Desiccator Cabinets, a constant dry nitrogen gas supply is required, connected to the nitrogen flowmeter on the desiccator cabinet. The flowmeter regulates the nitrogen gas flow (cu\/ft\/hr) to the plenum chamber of the desiccator with the nitrogen gas distributed uniformly through the perforated inside wall of the plenum chamber into each compartment.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eTDI Desiccator Ultra Nitro-Flow System\u003c\/strong\u003e\u003c\/p\u003e\n\u003cp\u003eAll TDI Acrylic Desiccators are constructed with Ultra Nitro-Flow compartment flow-throughs, which achieve a single pressure and atmosphere condition throughout the desiccator. This unique design allows maximum gas flow in both the vertical and horizontal directions and reduces higher moisture humidity conditions between compartments.\u003c\/p\u003e\n\u003cp\u003eThis flow design allows for a single automatic bleeder valve per multiple compartment cabinet and eliminates the need for expensive outlet valves for each compartment, required in typical competitor cabinets. The bleeder valve is located in the bottom of the lowest compartment and serves as an efficient outlet drain for the heavier high moisture atmosphere within the cabinet. This design also allows for a single #HM40 Nitro-Save® Humidity Control Monitor sensor system for multiple compartment desiccators.\u003c\/p\u003e\n\u003cp\u003e\u003cstrong\u003eIMPORTANT: Retro-Fit Kit requires removable back wall \u0026amp; for desiccators flow-through design between chambers.\u003c\/strong\u003e\u003c\/p\u003e\n","brand":"TDI International","offers":[{"title":"Default Title","offer_id":54159928459583,"sku":"NS16","price":3044.0,"currency_code":"USD","in_stock":true}],"thumbnail_url":"\/\/cdn.shopify.com\/s\/files\/1\/0991\/8477\/1391\/files\/TDI-Nitro-Save.webp?v=1784832846","url":"https:\/\/tdiinternational.com\/products\/nitro-save","provider":"TDI International","version":"1.0","type":"link"}